VGCollect Forum
General and Gaming => Hardware and Tech => Topic started by: shepard11 on June 03, 2017, 07:29:22 pm
-
I've been getting a lot of GB, GBC, GBA games lately. I usually just clean them with a q-tip and 90% rubbing alcohol. I got them all to work but one. Everytime I put in the GBA SP or the Super Game Boy it loads the Gameboy logo but then goes to a solid white scene. Any suggestions on what I could do to make it work? Or do y'all think it's just fried and I just need to get a replacement? Thanks in advance.
-
take it apart and use a pencil eraser on the contacts
-
take it apart and use a pencil eraser on the contacts
Up and down, not side to side.
-
Thanks for the heads up I'll try that.
-
take it apart and use a pencil eraser on the contacts
Up and down, not side to side.
I've had a few NES carts that wouldn't work even after my initial qtip cleaning. When this happens I open them up and about 90% of the time has some sort of soda slime that snuck into the cart (this is when I say WHO WERE THESE PEOPLE?). After cleaning that filth out and retrying they will usually work.
-
.
-
Came in here to post pretty much exactly what these above did. The pencil eraser thing has saved me a ton of times on carts.
I've heard the white plastic-y erasers (often Japanese) work best. People have a preference?
-
.
-
Came in here to post pretty much exactly what these above did. The pencil eraser thing has saved me a ton of times on carts.
I've heard the white plastic-y erasers (often Japanese) work best. People have a preference?
I just use either the old fashioned pink rubber one or this one:
https://www.amazon.com/Itemap-Rubber-Pencil-Writing-Nursery/dp/B0744FX22P/ref=sr_1_28?ie=UTF8&qid=1505143616&sr=8-28&keywords=rubber+pencil+eraser
Good to know! Yeah, those white ones were the ones I was thinking of.
Also, are they really suggesting an eraser as a nursery gift? ???
-
.
-
Adding to this topic, my friend found an old gameboy advance video cart under some melted snow in an orchard near his home. I've tried cleaning the contacts and any residue on the board, but playing it on a gba shows that, whatever i do,i always get a broken nintendo logo on startup. Any fix for this? GBA videos are pretty valuable, I'd hate for this one to go to waste.
-
Sometimes on Gameboy cartridges something goes loose on the inside from being dropped on a hard surface in my experience or from careless handling. I mean a loose part in the cartridege itself I think would be the problem sometimes right guys? ???
Adding to this topic, my friend found an old gameboy advance video cart under some melted snow in an orchard near his home. I've tried cleaning the contacts and any residue on the board, but playing it on a gba shows that, whatever i do,i always get a broken nintendo logo on startup. Any fix for this? GBA videos are pretty valuable, I'd hate for this one to go to waste.
video relating to topic
https://www.youtube.com/watch?v=RQb9AMt-xlE
Yea good call on your part for trying to reuse the hardware. But in my opinion you should look for rust spots because once electronic hardware gut like the kind found in all computer electronics gets totally rusty it is usually not good to use anymore. But sometimes it can be salvageable just like ET for the Atari 2600 game cartridges working found dumped in the elements of a city landfill or junkyard.
-
I've tried a couple things, all depending on how confident you are are in your skills:
I can second the alcohol and eraser. These carts are decades old, a lil' eraser, alcohol, and brasso aren't going to ruin them...
Step one for me if 90% alcohol and qtip doesn't work: Brass Polish (e.g. Brasso). A lot of people will warn against this, simply because it can leave residue. But, I highly recommend this. It will not only get gunk off the pins, it will remove any corrosion from years of air/humidity (kids blowing oreo spit into them) exposure. My suggestion is to remove the board and use something like an "extra hand" to hold the board while you let it dry. You only need the tiniest bit, and don't forget to do both sides. Use alcohol and a qtip afterwards to remove any leftover residue and make sure that it is completely dry before testing. Any moisture leftover can fry the board.
Step two is the above does not work is to locate the memory chip on the boards and refresh the solder. If it is loading a white screen after the gameboy logo it can be because the content after the gameboy screen is failing to load to memory because of a bad joint. These chips are usually the largest on the board, and there may be two, or more. They generally have 16-20 pins (for GB). You really only need enough solder to get the tip of your iron hot and need only to touch each joint to "warm" them up. Sometimes I just swipe the hot iron over the joints from one direction to the other. You don't need to put pressure on the joints or apply significant amounts of solder. I've fortunately only had to do this a handful of times and has worked in all but one (RIP Final Fantasy Legends II). Only on a couple have I had to actually re-solder one of the joints.
Again, only do these if you are comfortable with using brass polish and comfortable with your soldering skills!
Good luck!
Also,
Sometimes on Gameboy cartridges something goes loose on the inside from being dropped on a hard surface in my experience or from careless handling. I mean a loose part in the cartridege itself I think would be the problem sometimes right guys? ???
Totally agree, had a copy of Starfox that wouldn't load. Found out the tab holding the board in place was broken, so when I would insert the cart in the SNES the board would just float up into the cart instead of seating into the pins. I hot glued a cut up piece of old credit card where the broken piece was and it worked!